Exactly How to Remove and Change a Bathtub.
Exactly How to Remove and Change a Bathtub.
Blog Article
We have discovered this article pertaining to How to Install a Bathtub Yourself listed below on the net and believe it made perfect sense to relate it with you here.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have currently bought a new tub as well as do not require to transform the arrangement of your previous supply of water pipes.
Your devices and also product list should comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines are in place in between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub till the spirit level reviews degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and additionally check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the bath tub has been utilized at the very least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, leading to complications with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was really useful. Don't hesitate to take the opportunity to distribute this article if you liked it. Thanks for your time spent reading it.
Schedule Report this page